Leads4pass Best Exam Dumps Training Resources Free Update

High quality Cisco CCNA 200-125 dumps exam training resources in PDF format download free try. The best and most updated latest Cisco CCNA 200-125 dumps pdf materials and vce youtube demo free shared from leads4pass.com. “CCNA Cisco Certified Network Associate CCNA (v3.0)” is the name of Cisco CCNA 200-125 exam dumps which covers all the knowledge points of the real Cisco exam. Cisco CCNA 200-125 dumps exam preparation kit contains all the necessary 200-125 questions that you need to know. 100% success and guarantee to pass Cisco 200-125 exam.

Download free latest Cisco 200-125 dumps pdf resources: https://drive.google.com/open?id=0B_7qiYkH83VRSnZDMkVUWDJzLWM

Download free latest Cisco 200-355 dumps pdf resources: https://drive.google.com/open?id=0B_7qiYkH83VRM01sZjQ2dUtRckU

Why Select Lead 4 pass?

Lead4pass is the best provider of IT learning materials and the right choice for you to pass Cisco 200-125 exam. Other brands started earlier, but the questions are not the newest and the price is relatively expensive. Lead4pass provide the latest real and cheapest questions and answers, help you pass Cisco 200-125 exam easily at first try.

Helpful Newest Cisco CCNA 200-125 Dumps Exam Questions And Answers (Q1-Q30)

QUESTION 1
Which range represents the standard access list?
A. 99
B. 150
C. 299
D. 2000
Correct Answer: A

QUESTION 2
If the primary root bridge experiences a power loss, which switch takes over?
A. switch 0004.9A1A.C182
B. switch 00E0.F90B.6BE3
C. switch 00E0.F726.3DC6
D. switch 0040.0BC0.90C5
Correct Answer: A

QUESTION 3
Refer to the exhibit.

What is the reason that the interface status is andquot;administratively down, line protocol downandquot;?
A. There is no encapsulation type configured.
B. There is a mismatch in encapsulation types.
C. The interface is not receiving any keepalives.
D. The interface has been configured with the shutdown command.
E. The interface needs to be configured as a DTE device.
F. The wrong type of cable is connected to the interface.
Correct Answer: D

QUESTION 4
Which statement about named ACLs is true?
A. They support standard and extended ACLs.
B. They are used to filter usernames and passwords for Telnet and SSH.
C. They are used to filter Layer 7 traffic.
D. They support standard ACLs only.
E. They are used to rate limit traffic destined to targeted networks.
Correct Answer: A

QUESTION 5
Refer to the exhibit.

Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)
A. SwitchA, Fa0/2, designated
B. SwitchA, Fa0/1, root
C. SwitchB, Gi0/2, root
D. SwitchB, Gi0/1, designated
E. SwitchC, Fa0/2, root
F. SwitchD, Gi0/2, root
Correct Answer: ABF

QUESTION 6
Which three of these statements regarding 802.1Q trunking are correct? 200-125 dumps (Choose three.)
A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.
Correct Answer: ACE

QUESTION 7
Scenario
Refer to the topology. Your company has decided to connect the main office with three other remote branch offices using point-to-point serial links.
You are required to troubleshoot and resolve OSPF neighbor adjacency issues between the main office and the routers located in the remote branch offices.








An OSPF neighbor adjacency is not formed between R3 in the main office and R5 in the Branch2 office. What is causing the problem?
A. There is an area ID mismatch.
B. There is a PPP authentication issue; a password mismatch.
C. There is an OSPF hello and dead interval mismatch.
D. There is a missing network command in the OSPF process on R5.
Correct Answer: C

QUESTION 8
Which feature is config by setting a variance that is at least 2 times the metric?
A. unequal cost load balancing
B. path selection
C. equal cost load balancing
D. path count
Correct Answer: A

QUESTION 9
Which three encapsulation layers in the OSI model are combined into the TCP/IP application layer?(Choose three)
A. Session
B. transport
C. presentation
D. application
E. data-link
F. network
Correct Answer: ACD

QUESTION 10
When a router is unable to find a known route in the routing table,how dose it handle the pacet?
A. It sends the packet to the next hop address
B. It sends the packet to the gateway of last resort
C. It discards the packet
D. It sends the packet over the route with the best metric
Correct Answer: B

QUESTION 11
Which three are valid modes for a switch port used as a VLAN trunk? (Choose three.)
A. transparent
B. auto
C. on
D. desirable
E. blocking
F. forwarding
Correct Answer: BCD

QUESTION 12
Which two components are used to identify a neighbor in a BGP configuration? (Choose two.)
A. autonomous system number
B. version number
C. router ID
D. subnet mask
E. IP address
Correct Answer: AE

QUESTION 13
While troubleshooting a connection problem on a computer, you determined that the computer can ping a specific web server but it cannot connect to TCP port 80 on that server. Which reason for the problem is most likely true?
A. A VLAN number is incorrect.
B. A Route is missing
C. An ARP table entry is missing.
D. An ACL is blocking the TCP port.
Correct Answer: D

QUESTION 14
Which two statements about IPv6 router advertisement messages are true? (Choose two.)
A. They use ICMPv6 type 134.
B. The advertised prefix length must be 64 bits.
C. The advertised prefix length must be 48 bits.
D. They are sourced from the configured IPv6 interface address.
E. Their destination is always the link-local address of the neighboring node.
Correct Answer: AB

QUESTION 15
Refer to the graphic.

R1 is unable to establish an OSPF neighbor relationship with R3. What are possible reasons for this problem? (Choose two.)
A. All of the routers need to be configured for backbone Area 1.
B. R1 and R2 are the DR and BDR, so OSPF will not establish neighbor adjacency with R3.
C. A static route has been configured from R1 to R3 and prevents the neighbor adjacency from being established.
D. The hello and dead interval timers are not set to the same values on R1 and R3.
E. EIGRP is also configured on these routers with a lower administrative distance.
F. R1 and R3 are configured in different areas.
Correct Answer: DF

QUESTION 16
Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? 200-125 dumps (Choose three.)

A. Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
B. Ensure that cables A and B are straight-through cables.
C. Ensure cable A is plugged into a trunk port.
D. Ensure the switch has power.
E. Reboot all of the devices.
F. Reseat all cables.
Correct Answer: BDF

QUESTION 17
Which three circumstances can cause a GRE tunnel to be in an up/down state? (Choose three.)
A. The tunnel interface IP address is misconfigured.
B. The tunnel interface is down.
C. A valid route to the destination address is missing from the routing table.
D. The tunnel address is routed through the tunnel itself.
E. The ISP is blocking the traffic.
F. An ACL is blocking the outbound traffic.
Correct Answer: BCD

QUESTION 18
A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?
A. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# no shut
B. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation ppp Main(config-if)# no shut
C. Main(config)# interface serial 0/0 Main(config-if)# ip address 172.16.1.1 255.255.255.252 Main(config-if)# encapsulation frame-relay Main(config-if)# authentication chap Main(config-if)# no shut
D. Main(config)# interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(configif)#encapsulation ietf Main(config-if)# no shut
Correct Answer: B

QUESTION 19
Refer to the exhibit.

Which three statements correctly describe Network Device A? (Choose three.)
A. With a network wide mask of 255.255.255.128, each interface does not require an IP address.
B. With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
C. With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.
D. With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
E. With a network wide mask of 255.255.254.0, each interface does not require an IP address.
Correct Answer: BDE

QUESTION 20
Which IPV6 feature is supported in IPV4 but is not commonly used?
A. unicast
B. multicast
C. anycast
D. broadcast
Correct Answer: C

QUESTION 21
Refer to the exhibit.

Which of these statements correctly describes the state of the switch once the boot process has been completed?
A. As FastEthernet0/12 will be the last to come up, it will be blocked by STP.
B. Remote access management of this switch will not be possible without configuration change.
C. More VLANs will need to be created for this switch.
D. The switch will need a different IOS code in order to support VLANs and STP.
Correct Answer: B

QUESTION 22
Which set of commands is recommended to prevent the use of a hub in the access layer?
A. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security maximum 1
B. switch(config-if)#switchport mode trunk switch(config-if)#switchport port-security mac-address 1
C. switch(config-if)#switchport mode access switch(config-if)#switchport port-security maximum 1
D. switch(config-if)#switchport mode access switch(config-if)#switchport port-security mac-address 1
Correct Answer: C

QUESTION 23
If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? (Choose two.)
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
Correct Answer: CE

QUESTION 24
What is the effect of using the service password-encryption command?
A. Only the enable password will be encrypted.
B. It will encrypt all current and future passwords.
C. It will encrypt the secret password and remove the enable secret password from the configuration.
D. Only the enable secret password will be encrypted.
E. Only passwords configured after the command has been entered will be encrypted.
Correct Answer: B

QUESTION 25
Which two statements about IPv4 multicast traffic are true? (Choose two.)
A. It burdens the source host without affecting remote hosts.
B. It uses a minimum amount of network bandwidth.
C. It is bandwidth-intensive.
D. It simultaneously delivers multiple streams of data.
E. It is the most efficient way to deliver data to multiple receivers.
Correct Answer: DE

QUESTION 26
Refer to the exhibit.

The speed of all serial links is E1 and the speed of all Ethernet links is 100 Mb/s. A static route will be established on the Manchester router to direct traffic toward the Internet over the most direct path available. What configuration on the Manchester router will establish a route toward the Internet for traffic that originates from workstations on the Manchester LAN?
A. ip route 0.0.0.0 255.255.255.0 172.16.100.2
B. ip route 0.0.0.0 0.0.0.0 128.107.1.1
C. ip route 0.0.0.0 255.255.255.252 128.107.1.1
D. ip route 0.0.0.0 0.0.0.0 172.16.100.1
E. ip route 0.0.0.0 0.0.0.0 172.16.100.2
F. ip route 0.0.0.0 255.255.255.255 172.16.100.2
Correct Answer: E

QUESTION 27
When a router undergoes the exchange protocol within OSPF, in what order does it pass through each state?
A. exstart state andgt; loading state andgt; exchange state andgt; full state
B. exstart state andgt; exchange state andgt; loading state andgt; full state
C. exstart state andgt; full state andgt; loading state andgt; exchange state
D. loading state andgt; exchange state andgt; full state andgt; exstart state
Correct Answer: B

QUESTION 28
What are two benefits of private IPv4 IP addresses? 200-125 dumps (Choose two.)
A. They are routed the same as public IP addresses.
B. They are less costly than public IP addresses.
C. They can be assigned to devices without Internet connections.
D. They eliminate the necessity for NAT policies.
E. They eliminate duplicate IP conflicts.
Correct Answer: BC

QUESTION 29
Which statement about slow inter VLAN forwarding is true?
A. The VLAN is experiencing slowness in the point-to-point collisionless connection.
B. The VLANs are experiencing slowness because multiple devices are connected to the same hub.
C. The local VLAN is working normally, but traffic to the alternate VLAN is forwarded slower than expected.
D. The entire VLAN is experiencing slowness.
E. The VLANs are experiencing slowness due to a duplex mismatch.
Correct Answer: E

QUESTION 30
which two steps must you perform to enbale router-on-stick on a switch ?(choose two)
A. connect the router to a trunk port
B. config the subint number exactly the same as the matching VLAN
C. config full duplex
D. cofigure an ip route to the vlan destn net
E. assign the access port to the vlan
Correct Answer: AB

Here Are Some Reviews From Our Customers:

You can click here to have a review about us: https://www.resellerratings.com/store/lead4pass

Useful Cisco CCNA 200-125 dumps pdf practice files and study guides free download from lead4pass. Latest Cisco CCNA 200-125 dumps pdf training resources which are the best for clearing 200-125 exam test, and to get certified by Cisco CCNA. If you are looking to get CCNA certification by passing exam 200-125 then you can pass it in one go.

Best Cisco CCNA 200-125 dumps vce youtube demo:

https://youtu.be/nF4Ul2viODM